How to Put a Bike Tire Back on the Rim? (Solved)


Our blog post today will show you How to put a bike tire back on the rim. You can easily Bikes can be a great way to get around but they’re only as good as their tires. When a tire goes flat, it’s often hard to find someone with the right tools and expertise to repair or replace them.

So what do you do when your bike starts going off the beaten path? In this article, we’ll discuss how to put a bike tire back on the rim so you don’t have to worry about being stranded again. You can easily perform this task by following the steps listed below.

  1. Firstly, watch for any arrows the manufacturer may have provided to aid you in the tire installation. The sidewalls of the wheel will be marked with arrows indicating the direction of rotation. Direction orientation is not always present in tires, but almost every tire has tread on it. You have to check that the tread is going in the right direction before mounting the tire on the rim. To sum it up, the tread would have to go along with the wheel. 
  2. While installing the tire, the label is often placed directly over where the valve is, as is common practice among mechanics. In this way, the hole would be visible when you pump up the tube if you have a flat. This makes fixing flats much easier.
  3. Now install one bead at a time by putting one side on. With your hands, place the tire bead on the rim. In the event that the tire bead cannot be seated using your hand, the tire lever can be used. Make sure that you use tire levers carefully so that you do not pinch the inner tube. 
  4. After that, take your tube and inflate it slightly, just so it becomes round and holds its shape. This is because it is easier to put inside the tire, and also when you are installing the other side of the tire, you won’t pinch it.
  5. Pass the tube over the rim sidewall and fit it into the rim cavity. You should start by inserting the valve, followed by pulling the tire over the tube. 
  6. As soon as you have the tube inserted inside the tire and rim, you will install the second bead to the rim.
  7. It’s just a matter of pushing the tire on, using your hands. Be careful not to pinch the tube. It’s important to not let the tube hang out here because it may pinch. While holding the tire, go around the whole circle. You can sometimes find it difficult; if that happens, use the tire lever and be careful not to pinch the tube. 
  8. Ensure that the tire is properly seated once it is mounted on the rim. What it means is that most tires have a seam running around them, and that seam should be even on both sides. This is crucial since not doing so may cause a blowout. Hence, be sure to check each side of the tire for proper bead seating and signs of the inner tube poking through. In case of need, reinstall.
  9. It is now time to start inflating the tire. Keep checking the seam on the tire as you pump it up to ensure that it is sitting correctly. Check the bead on both sides again after inflation at low pressure. If needed, make adjustments.
  10. You can use soapy water to lubricate a tire bead that is stuck below the rim if adding air pressure does not correct it. Grease and oil should not be used.
  11. Now, inflate the tire to its maximum pressure and monitor your gauge on the pump to make sure it is in the correct pressure range. Tire pressure differs based on the type and is stated on the sidewall of each tire.
  12. As soon as the pressure is up, be sure to tighten that screw on the Presta valve. If it’s a Schrader valve, be sure to put a cap on it so dirt doesn’t get inside the valve. When tightening nuts, do not use tools like pliers or wrenches – use your fingers.

Read this article:

How to mount women’s bike on the bike rack?


A bike tire can go flat at the most inconvenient times. It could be the middle of a trip or even during the ride. A flat tire can be dangerous and cause you to lose control of your bike. It can also keep you from making it back home. Here’s how to put the tire back on the rim.

If you are having issues putting your tire back on the rim, don’t worry. You can always get help from a bike shop or someone who has experience with bikes. We hope this blog post was helpful to you!